Important Information

Troubleshooting RMA

General Instructions

Troubleshooting RMA

 

General Information

 

 

Datasheet

FM4200 User Manual v1.6.pdf

FM4100_User_Manual_v3.0.pdf

FM4100_User_Manual_v3.0.pdf

FM1100_User_Manaul_v015.pdf

image2015-5-15 11:27:48.png

 

Navigate LED operation (GPS Signal)

If ignition is ON and connected, the Navigate LED must blink every second.

Behavior
Meaning
Permanently switched onGPS signal is not received
Blinking every secondNormal mode, GPS is working
Off

GPS is turned off because of deep sleep mode

Or GPS antenna short circuited

Status LED operation (GSM)

If ignition is ON and connected, the LED must blink every second and faster if data is transferred.

Behavior
Meaning
Blinking every secondNormal mode
Blinking every 2 secondsDeep sleep mode
Blinking fast for a short timeModem activity
Blinking fast constantlyBoot mode
Off

Device is not working or device firmware being flashed

 

Car-10 (Teltonika FM1100) Standard installation with Main Power, Ground and Ignition

 

Refer to the sticker on the device to find the correct wire for ignition, main power and ground!


 


PIN

Typ

Color

Required

Description

1VCC DC YESPermanent power (10-30 Volt)
2OUT2  Output 2
3OUT1  Output 1
4DIN 2 optionalInput 2: e.g. privat switch

5

DIN 1

 

YES

Input 1: connect with ignition signal

6

GND

 

YES

connect with ground

7

AIN 1

 

 

Analogue input (voltage values)

8Data  Dallas iButton driver data
9DIN 3  Input 3
10UCC  Dallas iButton


 

Positioning of the device with GPS antenna insde the device

The device shall be placed UNDER the plastic dashbord with the sticker showing to the sky.

 

Positioning of the device (optional)

If acceleration plays a role, the device should be positioned horizontally and the main wire should show to the back or in driving direction



Installation Tests:

see Installation Tests and Reporting

FM41 (GFSx44) Tracking Device

FM41 Plug & Pins

 

PIN

Type

Colour

Description

1

VCC (10-30) V DC

Black

Power + 10 V  - 30 V DC Direct Current

11

GND (12-30) V DC

Black

Ground

16

DIN 1

Black

Digital input / Ignition

LED's

 

FM22 (GFSx22) Connection Plan

The GSM antenna is integrated in the device. You have to open the device for inserting the SIM card.

 

PIN

Type

Colour

Description

1

GND (12-30) V DC

Black

Ground

2

VCC (10-30) V DC

Red

Permanent power + 10 V  - 30 V Direct Current

3

DIN 1

Yellow

Digital input 1 / Ignition

LED's

FM42 (GFSx44) Connection Plan

 

 

The GSM antenna is integrated in the device. You have to open the device for inserting the SIM card.

The following diagram shows how to connect to main power, ground and ignition.

 

 

PIN

Type

Colour

Description

1

GND (12-30) V DC

Black

Ground

11

VCC (10-30) V DC

Red

Power + 10 V  - 30 V Direct Current

15

DIN 1

Yellow

Digital input 1 / Ignition

 

LED's

 

 



Accessories

Accessories only work with the right tracking unit GFSx44 and are not included in the standard delivery.

You only have to read this chapter if you need to fix the accessories.

Take care that the FM4100 and FM4200 require DIFFERENT wiring connections.

It might be necessary to configure additional settings in the software in order to use the accessories.

Driver Identification via I-Button Installation for FM4100 only


The accessories must be provided by the same vendor as the tracking unit or it must be guaranteed that exactly the same type ibuttons and readers is used to make it work:

The I-Button Installation is only necessary for vehicles that shall be equipped with a driver identification. I-Button Installation only works with FM41 Box!

Connect and test the following:

 

PIN

Type

Colour

Description

11

GND

Grey

iButton cable

8

Data

White

iButton cable

 

To complete the installation, the iButton system must be tested via SMS. In order to test your installation, you must attach an iButton chip to the reader and send an SMS-Test to the box

TESTS

LED lights ok

LED lights NOT OK

SMS-TEXT to GSM number

Feedback SMS (compulsory, if no feedback -> error)

SMS Test OK

SMS Test NOT OK

GPS

-

-

USR PWD readio 78

IO ID:78 Value:318767235

Value > 0

When you receive a Value, the iButton Reader works

No feedback or “IO ID:78 Value:0”

To test the installation, make sure that the ibutton is on the reader.

 

Driver Identification via I-Button and Buzzer - FM41

Attention! This feature requires also a firmware update of each tracking unit. Contact your dealer for more information.

In case if engine is started without connected Ibutton, in 5 seconds the external Buzzer connected to FM4100 is starting alarming. Alarming stops after Ibutton is connected or/and Vehicle ignition is off. . The digital input 3 must be connected to ignition.

Connection Plan:


PIN

Type

Colour

Description

11

GND

Grey

iButton cable

8

Data

White

iButton cable

18

DIN3

 

Ignition must be connected to DIN3 (not DIN1)

1

VCC Power

Green

Must be connected to Buzzer and reader

4

OUT3

Yellow

Must be connect to Buzzer and

 

 

To complete the installation, the iButton system must be tested via SMS. In order to test your installation, you must attach an iButton chip to the reader and send an SMS-Test to the box

 

TESTS

LED lights ok

LED lights NOT OK

SMS-TEXT to GSM number

Feedback SMS (compulsory, if no feedback -> error)

SMS Test OK

SMS Test NOT OK

GPS

-

-

USR PWD readio 78

IO ID:78 Value:318767235

Value > 0

When you receive a Value, the iButton Reader works

No feedback or “IO ID:78 Value:0”

Driver Identification via I-Button and Buzzer - FM4200

Attention! This feature requires also a firmware update of each tracking unit. Contact your dealer for more information. In case if engine is started without connected Ibutton, the external Buzzer connected to device is starting alarming. Alarming stops after Ibutton is connected or/and Vehicle ignition is off. The digital input 1 must be connected to ignition.

Connection Plan:

 

PIN

Type

Colour

Description

1

GND

Black

Grey iButton cable

13

1-Wire Data

 

White iButton cable

15

DIN1

Yellow

Ignition must be connected to DIN1

11

VCC Power

Red

Green iButton Cable

19

OUT1

 

Yellow iButton cable (based on ground) Must be connect to Buzzer and

11

VCC Power

Red

Red cable of alarm buzzer

19

OUT1

Black

Black cable of alarm buzzer must be connected to ground

Temperature Sensors for GFSx44 (FM4100)

 

The temperature sensor is converting temperature into „iButton signal“.

Sensor type must be DS1820-PUR-7M. Connect and test the following

PIN

Type

Colour

Description

20

PWD Data

 

Green cable of sensor

8

Data

 

Brown cable of sensor

11

GND

 

White cable of sensor

 

 

Test per SMS

Temperatur-Sensors FM4200

Sensor type must be DS1820-PUR-7M. Connect and test the following:

 

PIN

Type

Colour

Description

3

1 W PWD Data

 

Green cable of sensor

13

1 W Data

 

Brown cable of sensor

1

GND

 

White cable of sensor

 

 

Tests per SMS:

TESTS

LED lights ok

LED lights NOT OK

SMS-TEXT to GSM number

Feedback SMS (compulsory, if no feedback -> error)

SMS Test OK

SMS Test NOT OK

GPS

-

-

USR PWD readio 72

IO ID:78 Value:318767235

Value > 0

When you receive a Value, the iButton Reader works

No feedback or “IO ID:78 Value:0”

 

Installation Tests:

see Installation Tests and Reporting

Troubleshooting

see Troubleshooting RMA