Important Links

Troubleshooting RMA

General Instructions

Troubleshooting RMA

 

General Information

 

 

Datasheet

Installation

Power Consumption

Opreational Mode

Sleep Mode after 15-60 Min

Deep Sleep Mode

Supply Voltage

~ 250 mA

40-50mA

5-7 mA (a special config is necessary)

10-30V

LED's

At installation and for the vehicle-check you can observe the LED signals:

 

LED

Indication

Description

What do do

PWR (Green)

Solid On

Full operation mode

OK

1 blink (0.1 sec) every 10 sec.

Sleep mode

Activate ignition or move the box so that it wakes up

1 sec. on, 1 sec. off

GPS module off, external power lost, running on backup battery

Check the permanent power connection!

GPS (Red)

0.7 sec on, 0.7 sec off

Searching GPS signal

Go to an area with clear view to the open sky, re-locate the GPS antenna or replace GPS antenna

Solid on

GPS Fix/GPS OK

GPS is working

GSM (Red)

Off

GSM module off

 

0.7 sec on, 0.7 sec off

Searching GSM signal

Out of GSM area or SIM card problem

0.2 sec on, 0.2 sec off

Registered to GSM network

SIM active

2 blinks every 2 sec.

Connected to GPRS network

Active connection, data is sent via GPRS

Continous blinking

SIM PIN Error

De-activate PIN code

 

  Standard Installation (Permanent Power & Ignition)



 

Color

Type

Necessary

Description

GPS Antenna

GPS

Yes

Connect the GPS antenna to the right plug on the device

RED

Power

Yes

Mandatory Main Power + 10 V  - 30 V DC (Direct Current)

Black

GND

Yes

Mandatory Ground

Yellow

IN0(ACC)

Yes

Mandatory Ignition Input

Green

IN1 (positive)

Optional

Trigger input, connect to a signal or switch (+)

Blue

IN2 (negative)

Optional

Trigger input, connect to a negative signal or switch (-, active when connected to ground)

Violet

IN3 (negative9

Optional

Trigger input, connect to a negative signal or switch (-, active when connected to ground)

 

IN0 and IN1 are POSITIVE inputs (active if connected to V+ range from 3.7 – 40 V).

 Attention! IN2, IN3 are NEGATIVE inputs (active if connected to ground frange from 0.8 – 0V).

 All outputs are open collector type (grounded when enabled)

Installation Tests:

see GPS Installation App Tests and Documentation

 

Aktion

Erwartetes Ergebnis

GPS Antenna

GPS Antenne is fixed and the round part is facing the satelite!

Ignition is OFF

LED’s are on and permanet power is available on the power supply cable

Ignition is ON

A record with ignition on is written in the data tool.

Ignition OFF

A record with ignition off is written in the data tool.

500 meter driving outside with some ignition changes

The whole trip is recorded in the datatool.

All ignition changes are recorded.

 Accessoires

Accessories only work with the right tracking device and are not included in the standard delivery

Driver Identification via iButton with AT5 and passive Buzzer

 

Connect the red buzzer wire to permanent power and the black buzzer wire to the orange buzzer cable of the device

 

PIN

Type

Colour

Description

13

1Wire-Data

Green/white

iButton white wire

14

1 Wire GND

Black

iButton grey wire

15

Buzzer

Orange

Buzzer black cable

 

Tests:

The driver identification is managed by the tracking device firmware or the software (refer to the UserManual). The test is based on software-side logoutmode=2 (driver identification required with every new trip).

Action

Result

Ignition is ON without ibutton

You should hear the buzzer at least 5x

No driver is shown in the software

Place the button on the reader

The buzzer noise stops

The driverID is shown in the software

 

Temperatur Sensor

PIN

Type

Colour

Connect to

13

1Wire-IO Data

Green-white

Temperature sensor red wire

14

1 Wire GND

Black

Temperature white wire

 

Tests

Ignition on

The data tool shows an value in the column temp1

A record with ignition on is written in the data tool.

 

Optional Accessoires

Garmin mit FMI Kabel

A separate installation manual exists!

Sqarell CAN Bus Gerät

A separate installation manual exists!

RFID Reader

A separate installation manual exists!

Troubleshooting

see Troubleshooting RMA