Important Information

Troubleshooting RMA

General Instructions

Troubleshooting RMA

 

Datasheet

AK1 DM 20130121-1.pdf

 

Installation

Power Consumption

Opreational Mode

Sleep Mode after 15-60 Min

Deep Sleep Mode

Supply Voltage

~250 mA

25mA

5-7 mA (a special config is necessary)

10-30V

LEDs

At installation and for the vehicle-check you can observe the LED signals:

LED

Indication

Description

What do do

PWR (Green)

Solid On

Full operation mode

OK

1 blink (0.1 sec) every 10 sec.

Sleep mode

Activate ignition or move the box so that it wakes up

1 sec. on, 1 sec. off

GPS module off, external power lost, running on backup battery

Check the permanent power connection!

GPS (Red)

0.7 sec on, 0.7 sec off

Searching GPS signal

Go to an area with clear view to the open sky, re-locate the GPS antenna or replace GPS antenna

Solid on

GPS Fix/GPS OK

GPS is working

GSM (Red)

Off

GSM module off

 

0.7 sec on, 0.7 sec off

Searching GSM signal

Out of GSM area or SIM card problem

0.2 sec on, 0.2 sec off

Registered to GSM network

SIM active

2 blinks every 2 sec.

Connected to GPRS network

Active connection, data is sent via GPRS

Continous blinking

SIM PIN Error

De-activate PIN code

 

 

Standard Installation (Permanent Power & Ignition)

 

Cable

Type

Necessary

Description

GPS Antenna

GPS

Yes

Connect the GPS antenna with the device

RED

Power

Yes

Main Power + 10 V  - 30 V DC (Direct Current)

Black

GND

Yes

Ground

Yellow

IN0(ACC)

Yes

Ignition Input

Green

IN1/1W

Optional

Negative trigger input (works when connected to ground)

Or 1-wire ibutton data

Brown *!

IN2/O1/AI

Optional

Default: Output 1 (max 300 mA, open collector)

Or positive trigger input

Or analogue input (0 – 40 Volt DC)

Grey *!

IN3/O2

Optional

Default: Output 1 (max 300 mA, open collector)

Or negative trigger input (works when connected to ground)

 

*! Attention: the output/input of the brown and grey cable must be configured prior to the connection. Else the device will be damaged!

Installation Tests:

see GPS Installation App Tests and Documentation

Aktion

Erwartetes Ergebnis

GPS Antenna

GPS Antenne is fixed and the round part is facing the satelite!

Ignition is OFF

LED’s are on and permanet power is available on the power supply cable

Ignition is ON

An record with ignition on is written in the data tool.

Ignition OFF

An record with ignition off is written in the data tool.

500 meter driving outside with some ignition changes

The whole trip is recorded in the datatool.

All ignition changes are recorded.

Accessoires

Accessories only work with the right tracking device and are not included in the standard delivery.

Private Switch

The device has a second input (open collector => ground must be switched) what allows to add a private switch!

 

 

 

Einbautests:

Aktion

Erwartetes Ergebnis

Ignition ON

Private Switch OFF

A record with DI1 =>1, DI2=>0 is written in the data tool.

Private Switch ON

A record with DI1 =>1, DI2=>1 is written in the data tool.

Private Switch OFF

A record with DI1 =>1, DI2=>0 is written in the data tool.

 

Connecting iButton driver identification with special buzzer (no relais)

). If the buzzer is too loud, you can use isolation tape around it

 

Cable

Type

Necessary

Connect to

GPS antenna

GPS

Yes

To the tracking device

Red wire

PWR – Power
+ 10 V  - 30 V DC (direct current)

Yes

Permanent power

Yellow wire

ACC Positive Input

Yes

Ignition power

Black wire

GND GROUND

Yes

Ground

Green wire

IN1

Yes

iButton reader white wire (1 Wire data)

Grey wire

OUT2

Yes

Buzzer ground cable

*! danger: make sure that the output has been configured by the provider prior to connecting it

 Tests:

The driver identification is managed by the tracking device firmware or the software (refer to the UserManual). The test is based on software-side logoutmode=2 (driver identification required with every new trip).

Action

Result

Ignition is ON without ibutton

You should hear the buzzer at least 5x

No driver is shown in the software

Place the button on the reader

The buzzer noise stops

The driverID is shown in the software

Connecting iButton driver identification with buzzer and relais

To prevent interferences we recommend to connect the buzzer only via an automotive relais (12 or 24 volt). If the buzzer is too loud, you can use isolation tape around it.

 

Cable

Type

Necessary

Connect to

GPS antenna

GPS

Yes

To the tracking device

Red wire

PWR – Power
+ 10 V  - 30 V DC (direct current)

Yes

Permanent power

Yellow wire

ACC Positive Input

Yes

Ignition power

Black wire

GND GROUND

Yes

Ground

Green wire

IN1

Yes

iButton reader white wire (1 Wire data)

Grey wire

OUT2

Yes

Relais 86

Relay Connection

Make sure to connect according the relay numbers (the colours could be different

 

Wire

Connect

Necessary

Description

85 (black)

Permanent power from vehicle

Yes

Switching current

86 (green)

Tracking device OUT2 (ground is switched ON/OFF)

Yes

Switching current

87 (yellow)

Vehicle ground

Yes

Working current (ON if 86 is switchting ground)

30 (red)

Ground of buzzer

Yes

Working current (ON if 86 is switchting ground)

 

Connect to

iButton reader white cable (1 wire data)

Tracking device IN1/1 w (green cable)

iButton grey wire (ground)

Vehicle ground

Alert buzzer red wire

Tracking device ignition plus ACC (yellow cable)

Alert buzzer black wire

Relay 87 *!

*! danger: make sure that the output has been configured by the provider prior to connecting it

 Tests:

The driver identification is managed by the tracking device firmware or the software (refer to the UserManual). The test is based on software-side logoutmode=2 (driver identification required with every new trip).

Action

Result

Ignition is ON without ibutton

You should hear the buzzer at least 5x

No driver is shown in the software

Place the button on the reader

The buzzer noise stops

The driverID is shown in the software

Temperatur Sensor

The sensor is delivered by the manufacturer and converts the temperature value into an Dallas iButton signal. One tracking device can handle up to 2 sensors.

 

 

Connect to

sensor reader red cable (1 wire data)

Tracking device IN1/1 w (green cable)

Sensor black wire (ground)

Vehicle ground

Tests:

Aktion

Erwartetes Ergebnis

Ignition on

The data tool shows an value in the column temp1

A record with ignition on is written in the data tool.

Optional Accessoires

Garmin mit FMI Kabel

A separate installation manual exists!

Sqarell CAN Bus Gerät

A separate installation manual exists!

RFID Reader

A separate installation manual exists!

Troubleshooting

see Troubleshooting RMA