Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Table of Contents

Important Information

Troubleshooting RMA

General Instructions

Troubleshooting RMA

 

General Information

 

 

Datasheet

FM4200 User Manual v1.6.pdf

...

image2015-5-15 11:27:48.png

 

Navigate LED operation (GPS Signal)

If ignition is ON and connected, the Navigate LED must blink every second.

Behavior
Meaning
Permanently switched onGPS signal is not received
Blinking every secondNormal mode, GPS is working
Off

GPS is turned off because of deep sleep mode

Or GPS antenna short circuited

Status LED operation (GSM)

If ignition is ON and connected, the LED must blink every second and faster if data is transferred.

Behavior
Meaning
Blinking every secondNormal mode
Blinking every 2 secondsDeep sleep mode
Blinking fast for a short timeModem activity
Blinking fast constantlyBoot mode
Off

Device is not working or device firmware being flashed

 

Car-10 (Teltonika FM1100) Standard installation with Main Power, Ground and Ignition

 

Refer to the sticker on the device to find the correct wire for ignition, main power and ground!


Image Added

 


PIN

Typ

Color

Required

Description

1VCC DC YESPermanent power (10-30 Volt)
2OUT2  Output 2
3OUT1  Output 1
4DIN 2 optionalInput 2: e.g. privat switch

5

DIN 1

 

YES

Input 1: connect with ignition signal

6

GND

 

YES

connect with ground

7

AIN 1

 

 

Analogue input (voltage values)

8Data  Dallas iButton driver data
9DIN 3  Input 3
10UCC  Dallas iButton


 

Positioning of the device with GPS antenna insde the device

The device shall be placed UNDER the plastic dashbord with the sticker showing to the sky.

 

Image Added

Positioning of the device (optional)

If acceleration plays a role, the device should be positioned horizontally and the main wire should show to the back or in driving direction

Image AddedImage Added



Installation Tests:

see Installation Tests and Reporting

FM41 (GFSx44) Tracking Device

FM41 Plug & Pins

 

PIN

Type

Colour

Description

1

VCC (10-30) V DC

Black

Power + 10 V  - 30 V DC Direct Current

11

GND (12-30) V DC

Black

Ground

16

DIN 1

Black

Digital input / Ignition

LED's

 

FM22 (GFSx22) Connection Plan

The GSM antenna is integrated in the device. You have to open the device for inserting the SIM card.

...

PIN

Type

Colour

Description

1

GND (12-30) V DC

Black

Ground

2

VCC (10-30) V DC

Red

Permanent power + 10 V  - 30 V Direct Current

3

DIN 1

Yellow

Digital input 1 / Ignition

LED's

FM42 (GFSx44) Connection Plan

 

 

The GSM antenna is integrated in the device. You have to open the device for inserting the SIM card.

...

PIN

Type

Colour

Description

1

GND (12-30) V DC

Black

Ground

11

VCC (10-30) V DC

Red

Power + 10 V  - 30 V Direct Current

15

DIN 1

Yellow

Digital input 1 / Ignition

 

LED's

 

Teltonika FM1100

 

 

Image Removed

 

 

 

PIN

Typ

Color

Description

1VCC DC Permanent power (10-30 Volt)
2OUT2 Output 2
3OUT1 Output 1
4DIN 2 Input 2: e.g. privat switch

5

DIN 1

 

Input 1: connect with ignition signal

6

GND

 

connect with ground

7

AIN 1

 

Analogue input (voltage values)

8Data Dallas iButton driver data
9DIN 3 Input 3
10UCC Dallas iButton

Image Removed

Installation Tests:

see Installation Tests and Reporting



Accessories

Accessories only work with the right tracking unit GFSx44 and are not included in the standard delivery.

...

It might be necessary to configure additional settings in the software in order to use the accessories.

Driver Identification via I-Button Installation for FM4100 only


The accessories must be provided by the same vendor as the tracking unit or it must be guaranteed that exactly the same type ibuttons and readers is used to make it work:

...

To test the installation, make sure that the ibutton is on the reader.

 

Driver Identification via I-Button and Buzzer - FM41

Attention! This feature requires also a firmware update of each tracking unit. Contact your dealer for more information.

...

TESTS

LED lights ok

LED lights NOT OK

SMS-TEXT to GSM number

Feedback SMS (compulsory, if no feedback -> error)

SMS Test OK

SMS Test NOT OK

GPS

-

-

USR PWD readio 78

IO ID:78 Value:318767235

Value > 0

When you receive a Value, the iButton Reader works

No feedback or “IO ID:78 Value:0”

Driver Identification via I-Button and Buzzer - FM4200

Attention! This feature requires also a firmware update of each tracking unit. Contact your dealer for more information. In case if engine is started without connected Ibutton, the external Buzzer connected to device is starting alarming. Alarming stops after Ibutton is connected or/and Vehicle ignition is off. The digital input 1 must be connected to ignition.

...

PIN

Type

Colour

Description

1

GND

Black

Grey iButton cable

13

1-Wire Data

 

White iButton cable

15

DIN1

Yellow

Ignition must be connected to DIN1

11

VCC Power

Red

Green iButton Cable

19

OUT1

 

Yellow iButton cable (based on ground) Must be connect to Buzzer and

11

VCC Power

Red

Red cable of alarm buzzer

19

OUT1

Black

Black cable of alarm buzzer must be connected to ground

Temperature Sensors for GFSx44 (FM4100)

 

The temperature sensor is converting temperature into „iButton signal“.

...

PIN

Type

Colour

Description

20

PWD Data

 

Green cable of sensor

8

Data

 

Brown cable of sensor

11

GND

 

White cable of sensor

 

 

Test per SMS

Temperatur-Sensors FM4200

Sensor type must be DS1820-PUR-7M. Connect and test the following:

...

TESTS

LED lights ok

LED lights NOT OK

SMS-TEXT to GSM number

Feedback SMS (compulsory, if no feedback -> error)

SMS Test OK

SMS Test NOT OK

GPS

-

-

USR PWD readio 72

IO ID:78 Value:318767235

Value > 0

When you receive a Value, the iButton Reader works

No feedback or “IO ID:78 Value:0”

 

Installation Tests:

see Installation Tests and Reporting

Troubleshooting

see Troubleshooting RMA