Page tree
Skip to end of metadata
Go to start of metadata

Important Information

Troubleshooting RMA

General Instructions

Troubleshooting RMA

 

Important Information

Datasheet

 

Installation

Power Consumption

Opreational Mode

Sleep Mode after 15-60 Min

Deep Sleep Mode

Supply Voltage

~250 mA

25mA

5-7 mA (a special config is necessary)

10-30V

LEDs

At installation and for the vehicle-check you can observe the LED signals:

LED

Indication

Description

What do do

PWR (Green)

Solid On

Full operation mode

OK

1 blink (0.1 sec) every 10 sec.

Sleep mode

Activate ignition or move the box so that it wakes up

1 sec. on, 1 sec. off

GPS module off, external power lost, running on backup battery

Check the permanent power connection!

GPS (Red)

0.7 sec on, 0.7 sec off

Searching GPS signal

Go to an area with clear view to the open sky, re-locate the GPS antenna or replace GPS antenna

Solid on

GPS Fix/GPS OK

GPS is working

GSM (Red)

Off

GSM module off

 

0.7 sec on, 0.7 sec off

Searching GSM signal

Out of GSM area or SIM card problem

0.2 sec on, 0.2 sec off

Registered to GSM network

SIM active

2 blinks every 2 sec.

Connected to GPRS network

Active connection, data is sent via GPRS

Continous blinking

SIM PIN Error

De-activate PIN code

 

 

Standard Installation (Permanent Power & Ignition)

 

Cable

Type

Necessary

Description

GPS Antenna

GPS

Yes

Connect the GPS antenna with the device

RED

Power

Yes

Main Power + 10 V  - 30 V DC (Direct Current)

Black

GND

Yes

Ground

Yellow

IN0(ACC)

Yes

Ignition Input

Green

IN1/1W

Optional

Negative trigger input (works when connected to ground)

Or 1-wire ibutton data

Brown *!

IN2/O1/AI

Optional

Default: Output 1 (max 300 mA, open collector)

Or positive trigger input

Or analogue input (0 – 40 Volt DC)

Grey *!

IN3/O2

Optional

Default: Output 1 (max 300 mA, open collector)

Or negative trigger input (works when connected to ground)

 

*! Attention: the output/input of the brown and grey cable must be configured prior to the connection. Else the device will be damaged!

Installation Tests:

see GPS Installation App Tests and Documentation

Aktion

Erwartetes Ergebnis

GPS Antenna

GPS Antenne is fixed and the round part is facing the satelite!

Ignition is OFF

LED’s are on and permanet power is available on the power supply cable

Ignition is ON

An record with ignition on is written in the data tool.

Ignition OFF

An record with ignition off is written in the data tool.

500 meter driving outside with some ignition changes

The whole trip is recorded in the datatool.

All ignition changes are recorded.

Accessoires

Accessories only work with the right tracking device and are not included in the standard delivery.

Private Switch

The device has a second input (open collector => ground must be switched) what allows to add a private switch!

 

 

 

Einbautests:

Aktion

Erwartetes Ergebnis

Ignition ON

Private Switch OFF

A record with DI1 =>1, DI2=>0 is written in the data tool.

Private Switch ON

A record with DI1 =>1, DI2=>1 is written in the data tool.

Private Switch OFF

A record with DI1 =>1, DI2=>0 is written in the data tool.

 

Optional Accessoires

Garmin mit FMI Kabel

A separate installation manual exists!

Sqarell CAN Bus Gerät

A separate installation manual exists!

RFID Reader

A separate installation manual exists!

Troubleshooting

see Troubleshooting RMA

  • No labels